![]() Stainless steel filament exit guide with 0.2-0.3mm clearance to drive gears for best TPU printing experience and extreme wear resistance when using abrasive filaments.Flipped drive gears – filament path closer to the extruder center for a more balanced design and perfect fit on delta printers as well.New motor design offers ~40% increase in extrusion force in real printing conditions and much improved acceleration performance.Smaller more compact dimensions (11.6% shorter).Shorter hardened drive gears 11mm vs 15mm manufactured by Bondtech.He received many suggestions from community as well. The new Orbiter v2.0 shares its concept design with the Orbiter v1.0 and 1.5 but it has been completely redesigned from scratch. Its precision design and advanced features make it an excellent choice for those looking to take their 3D printing to the next level. Overall, the Orbiter Extruder V2.0 is a reliable and high-performing extruder that is perfect for both beginners and experienced 3D printing enthusiasts. Additionally, the extruder is equipped with a modular hotend design, allowing for easy maintenance and customization. There's a few videos I've found on the orbiter 1.5, but I'm unsure whether to follow them due to the wire colors being different (green yellow red and blue). This results in improved print quality and reduces the likelihood of filament slipping or jamming. ldo orbiter 2 wiring help So I'm unable to find a wiring diagram for going from the stock e3pro (with 4.2.2 board) cables to the orbiter 2.0. One of the standout features of the Orbiter Extruder V2.0 is its adjustable tension system, which allows users to fine-tune the amount of pressure applied to the filament. ![]() Large extrusion gears (13.5mm) and short filament path make it great choice for printing with flexible filament. With its precision-machined gears from Bondtech and high-torque stepper motor the Orbiter Extruder V2.0 can handle a wide range of filaments, including PLA, ABS, PETG and more. It features a lightweight and compact design, making it easy to integrate into any 3D printer setup. Therefore, retraction speed needs to be limited in the slicer to. Having high step/mm ratio for the Orbiter v2.0, limits the maximum extrusion speed the Trinamic driver can drive the Orbiter to about 40mm/s. M203 X16500.00 Y16500.00 Z1000.00 E3600.00 C5000 set maximum speeds (mm/min) Press in the 3010 axial fan in the middle with the fan wiring toward the left bottom side of the shroud (toward the wire guide part). M350 X16 Y16 Z16 E16 I1 configure microstepping with interpolation M350 C8 I0 configure microstepping without interpolation Really amazing how much power it has for the weight. Nice, I bought the full kit and really like the results on my ender 3. M569 P4 S0 physical drive 4 goes backwards (Coupler) Installed Orbiter extruder on Ender 5, very impressed with look and performance. M569 P3 S1 physical drive 3 goes forwards (E0) M569 P2 S0 physical drive 2 goes backwards (Z axis) M569 P1 S1 physical drive 1 goes forwards (Y axis) M569 P0 S1 physical drive 0 goes forwards (X axis) I have tried different currents 1400mA, 1000mA, 900mA and 700mA but still doing the same. Retraction: 1.2mm (for the volcano V6 hotend) Maximum instantaneous speed change (jerk): 300 mm/min(RRF), 5 (Marlin) Orbiter Extruder Step Motor NEMA14 36mm Round Pancake Motor for Voron Printer. Stepps: 655 stepps / mm 16 micro-stepping (for the 7.5:1 gearing ratio) Custom request of lead wires or motor cables for RobotDigg Stepper Motors. I have put the configuraton for the extruder as per instructions: I have also tried swapping the cables but is not working either. The connections are B, A, A, B on the duet, the same for my motor. Nor the board has problem because for ease of practicing I have tried driver3 and driver0. I have bought 4 motors from Wantai (36BYGH218, 1.8A, 1.8deg/step)and tested them all, so I do not think it is the motor's problem, because they are all doing the same noise like ggrrrrr, loosing steps. Unfortunately I am having problems with the motor. I have just instaled the new extruder, "The orbiter", for minimizing the weight.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |